LightSpion, BaseSpion and LabSpion base - version 2.51
Labarazzi - version 2.00
BaseSensor and LabSensor - version 3.46
LabFlicker - version 1.25
VX01 Controller - version 1.88
Date: 28-02-2022 08:36:38Build: 5974
VMS01 - 02_51 Beta NoForce 20220228083638 5974.firm
Improved connect to device timing
LightSpion, BaseSpion and LabSpion base - version 2.50
Date: 31-01-2022 06:33:46Build: 5947
VMS01 - 02_50 Beta NoForce 20220131063346 5947.firm
Improved spectrometer loading.
LightSpion, BaseSpion and LabSpion base - version 2.49
Date: 16-11-2021 15:17:55Build: 5945
VMS01 - 02_49 Beta NoForce 20211116151755 5945.firm
Bug fix: Auto c-plane can result system halted warning, has been fixed.
LightSpion, BaseSpion and LabSpion base - version 2.47
Date: 12-10-2021 09:31:57Build: 5937
VMS01 - 02_47 Beta NoForce 20211012093157 5937.firm
Bug fix: When using software version 6.10 or higher could measurement planes be slightly shifted, this has now been fixed.
LightSpion, BaseSpion and LabSpion base - version 2.46
Date: 02-09-2021 17:35:29Build: 5928
VMS01 - 02_46 Beta NoForce 20210902173529 5928.firm
Bug fix: System could sometimes detect LabTemp device and report firmware error even if no LabTemp device was connected, this has now been fixed.
LightSpion, BaseSpion and LabSpion base - version 2.45
Date: 01-02-2021 15:17:54Build: 5922
VMS01 - 02_45 Beta NoForce 20210201151754 5922.firm
Supporting new communication standard with enhanced error correction between sensor and mainboard. Supporting new UV-VIS sensor and LabRail communication standard. Added support for LabTemp. LabTemp communication update. Updated power readout method. Updated motor control.
LightSpion, BaseSpion and LabSpion base - version 2.40
Date: 25-09-2020 16:47:08Build: 5772
VMS01 - 02_40 Beta NoForce 20200925164708 5772.firm
Supporting new UV-VIS sensor and LabRail communication standard.
LightSpion, BaseSpion and LabSpion base - version 2.38
Date: 03-07-2019 11:01:14Build: 5340
VMS01 - 02_38 Beta NoForce 20190703110114 5340.firm
Minor bug fix when using swap motor function on BaseSpion
LightSpion, BaseSpion and LabSpion base - version 2.36
Date: 12-06-2018 11:10:47Build: 5295
VMS01 - 02_36 Beta NoForce 20180612111047 5295.firm
New power analyzer firmware v1.28 fixing failed power on/off reading sometimes at startup.
LightSpion, BaseSpion and LabSpion base - version 2.35
Date: 07-06-2018 09:44:46Build: 5293
VMS01 - 02_35 Beta NoForce 20180607094446 5293.firm
New power analyzer firmware v1.27 with higher accuracy is now also supported on LightSpion, must be used with Light Inspector v5.46 or later.
LightSpion, BaseSpion and LabSpion base - version 2.34
Date: 04-06-2018 16:03:22Build: 5286
VMS01 - 02_34 Beta NoForce 20180604160322 5286.firm
Power analyzer v1.27. Sample rate updated from 70K to 355K samples per second to increase power measurement accuracy. Power measurement now also performed during warmup, only supported Light Inspector 5.45 and newer.
LightSpion, BaseSpion and LabSpion base - version 2.33
Date: 13-03-2018 14:21:45Build: 5283
VMS01 - 02_33 Beta NoForce 20180313142145 5283.firm
Reset of CPU when unplugging USB and closing software (only Light Inspector 5.36 and newer). Supports Realtime tracking.
LightSpion, BaseSpion and LabSpion base - version 2.32
Date: 21-02-2017 11:20:32Build: 5158
VMS01 - 02_32 Beta NoForce 20170221112032 5158.firm
Power analyzer version 1.26 fixing issue with lamp not always turning off.
LightSpion, BaseSpion and LabSpion base - version 2.31
Date: 09-09-2016 17:18:00Build: 5155
VMS01 - 02_31 Beta NoForce 20160909171800 5155.firm
Power analyser update v1.25: Soft lamp off preventing high current spikes when lamp is an inductive load and turned off. High current spikes can result in USB disconnecting.
LightSpion, BaseSpion and LabSpion base - version 2.30
Date: 20-05-2016 15:51:16Build: 5152
VMS01 - 02_30 Beta NoForce 20160520155116 5152.firm
First version supporting BaseSpion. Power analyser updated: Systems using releay power switch will always turn on even if lamp has high in-rush current
LightSpion, BaseSpion and LabSpion base - version 2.27
Date: 19-02-2016 12:48:16Build: 5132
VMS01 - 02_27 Beta NoForce 20160219124816 5132.firm
Power analyzer firmware updated to improve sensitivity of power analyzer.
LightSpion, BaseSpion and LabSpion base - version 2.26
Date: 11-02-2016 16:02:42Build: 5129
VMS01 - 02_26 Beta NoForce 20160211160242 5129.firm
Motor voltage can be checked, giving warning if mains power is not plugged in.
LightSpion, BaseSpion and LabSpion base - version 2.25
Date: 25-99-2015 15:28:46Build: 5113
VMS01 - 02_25 Beta NoForce 20159925152846 5113.firm
First version with cone speed to support high res measurment of narrow beam angles at multiple c-planes
LightSpion, BaseSpion and LabSpion base - version 2.24
Date: 22-07-2015 21:15:51Build: 5082
VMS01 - 02_24 Beta NoForce 20150722211551 5082.firm
Support for LabSpion base lock detection
LightSpion, BaseSpion and LabSpion base - version 2.23
Date: 27-05-2015 15:05:43Build: 5072
VMS01 - 02_23 Beta NoForce 20150527150543 5072.firm
Lamp stays on when USB unplugged. Offset correction smoother power on. More stable power measurement v1.21. Double relay power on even at high start current.
LightSpion, BaseSpion and LabSpion base - version 2.21
Date: 13-05-2015 17:43:39Build: 5070
VMS01 - 02_21 Beta NoForce 20150513174339 5070.firm
Lamp stays on when USB unplugged. More stable power measurement v1.21. Double relay power on even at high start current. Smoother power sample.
LightSpion, BaseSpion and LabSpion base - version 2.20
Date: 01-04-2015 10:03:48Build: 5055
VMS01 - 02_20 Beta NoForce 20150401100348 5055.firm
More stable power measurement v1.20. Double relay support. Smoother power sample.
LightSpion, BaseSpion and LabSpion base - version 2.19
Date: 19-03-2015 14:17:34Build: 5052
VMS01 - 02_19 Beta NoForce 20150319141734 5052.firm
More stable power measurement v1.19. Double relay support. Smoother power sample.
LightSpion, BaseSpion and LabSpion base - version 2.16
Date: 09-09-2014 18:34:04Build: 5039
VMS01 - 02_16 Beta NoForce 20140909183404 5039.firm
Power relay support, smoother power sample. Motor contol bug fixed. Supprts new PCB. Auto power off at unplug and reset.
LightSpion, BaseSpion and LabSpion base - version 2.14
Date: 23-06-2014 18:38:14Build: 5035
VMS01 - 02_14 Beta NoForce 20140623183814 5035.firm
Motor contol bug fixed. Supprts new PCB. Auto power off at unplug and reset. Minor Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information
LightSpion, BaseSpion and LabSpion base - version 2.11
Date: 10-06-2014 16:14:47Build: 5012
VMS01 - 02_11 Beta NoForce 20140610161447 5012.firm
Supprts new PCB. Auto power off at unplug and reset. Minor Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information
LightSpion, BaseSpion and LabSpion base - version 2.08
Date: 13-05-2014 22:01:49Build: 5008
VMS01 - 02_08 Beta NoForce 20140513220149 5008.firm
Supprts new PCB. Auto power off at unplug and reset. Minor Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information
LightSpion, BaseSpion and LabSpion base - version 2.07
Date: 15-02-2014 17:18:14Build: 4971
VMS01 - 02_07 Beta NoForce 20140215171814 4971.firm
Auto power off at unplug and reset. Minor Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information
LightSpion, BaseSpion and LabSpion base - version 2.06
Date: 10-02-2014 22:15:52Build: 4966
VMS01 - 02_06 Beta NoForce 20140210221552 4966.firm
Minor Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information. High res delay for flicker test. First version for 2 phase motor control
LightSpion, BaseSpion and LabSpion base - version 2.06
Date: 10-02-2014 22:07:58Build: 4965
VMS01 - 02_06 Beta NoForce 20140210220758 4965.firm
Miner Status read bug fixed. Remote VersaPic support. 2 motor driver. 2048 pixel support. Read motor type information. High res delay for flicker test. First version for 2 phase motor control
_________________________________________________________________________________________________________________
Date: 12-11-2021 15:52:54Build: 0
LABZZI1 - 02_00 Release NoForce 20211112155254 0.firm
Minor main screen changes. WF1 and WF26 swapped place. Waveforms can now be loaded back and forth in software. Mayor signal generator update to reduce bugs. Amp scaling now works with on board generated signals. Intensity is not specified in approximate lumens
Labarazzi - version 1.18
Date: 07-10-2021 16:52:51Build: 0
LABZZI1 - 01_18 Beta NoForce 20211007165251 0.firm
Added PstLM 1 SVM 1 WF26. Running 5% intensity change and flash block Read write enabled
Labarazzi - version 1.16
Date: 05-10-2021 16:49:50Build: 0
LABZZI1 - 01_16 Beta NoForce 20211005164950 0.firm
Live Intensity Change
Labarazzi - version 1.15
Date: 24-09-2021 15:54:40Build: 0
LABZZI1 - 01_15 Beta NoForce 20210924155440 0.firm
Improved USB communication under startup.
Labarazzi - version 1.14
Date: 17-09-2021 16:55:28Build: 0
LABZZI1 - 01_14 Beta NoForce 20210917165528 0.firm
Second version of Labarazzi firmware. Now with MD signal generator and waveform USB transfer
Labarazzi - version 1.12
Date: 16-08-2021 14:10:42Build: 0
LABZZI1 - 01_12 Beta NoForce 20210816141042 0.firm
First version of Labarazzi firmware.
_________________________________________________________________________________________________________________
Date: 17-02-2022 07:26:49Build: 6552
LABSEN1 - 03_46 Beta NoForce 20220217072649 6552.firm
New firmware 1.22 for BaseSpion position detection board to improve position detection. Position detection must be re-calibrated for improvement to come into effect. Added special internal byte delay firmware upload method.
BaseSensor and LabSensor - version 3.45
Date: 15-07-2021 15:02:54Build: 6551
LABSEN1 - 03_45 Beta NoForce 20210715150254 6551.firm
Bug fix: Internal setup memory offset aligned, can result in custom calibration set in older version not loading in newer Light Inspector version 6.01.1 to 6.21.
BaseSensor and LabSensor - version 3.44
Date: 01-06-2021 09:20:24Build: 6542
LABSEN1 - 03_44 Beta NoForce 20210601092024 6542.firm
Double bib sound added to LabSensor making it easier to know when distance measurement has been started.
BaseSensor and LabSensor - version 3.43
Date: 12-03-2021 10:35:03Build: 6532
LABSEN1 - 03_43 Beta NoForce 20210312103503 6532.firm
Laser load error can result in laser not working has been fixed. Version supporting new UV sensor. Supports new commode communication standard for LabRail. Supports LabSensor Model2 with display. Basespion now works with new software. New laser load direct bug fixed.
BaseSensor and LabSensor - version 3.34
Date: 23-09-2019 10:36:51Build: 5822
LABSEN1 - 03_34 Beta NoForce 20190923103651 5822.firm
Increased stability when laser on button is pushed on LabSensor.
BaseSensor and LabSensor - version 3.33
Date: 13-08-2019 11:18:15Build: 5819
LABSEN1 - 03_33 Beta NoForce 20190813111815 5819.firm
Laser distance measurement of black surface could make sensor reset, has been fixed.
BaseSensor and LabSensor - version 3.32
Date: 16-11-2018 16:20:41Build: 5808
LABSEN1 - 03_32 Beta NoForce 20181116162041 5808.firm
Laser distance measurement now more stable. Supporting new laser communication port. Minor bug fix for new laser port.
BaseSensor and LabSensor - version 3.30
Date: 11-01-2018 11:48:09Build: 5664
LABSEN1 - 03_30 Beta NoForce 20180111114809 5664.firm
Supporting new driver board for sensor. New internal sync timer functionality for more precise tracking of measurements and faster setting of integration time.
BaseSensor and LabSensor - version 3.29
Date: 05-10-2017 14:18:10Build: 5530
LABSEN1 - 03_29 Beta NoForce 20171005141810 5530.firm
Improved BaseTracker v1.21 sensitivity. New internal sync timer functionality for more precise tracking of measurements and faster setting of integration time.
BaseSensor and LabSensor - version 3.23
Date: 20-06-2017 16:01:04Build: 5371
LABSEN1 - 03_23 Beta NoForce 20170620160104 5371.firm
Includes software opdater for BaseSpion distance detector, new base distance sensor firmware 1.19 with better sensitivity. Supports new spectrometer driver boards.
BaseSensor and LabSensor - version 3.22
Date: 10-11-2016 14:53:51Build: 5204
LABSEN1 - 03_22 Beta NoForce 20161110145351 5204.firm
Supporting BaseSensor for BaseSpion. Sensor type detection bug fixed.
BaseSensor and LabSensor - version 3.21
Date: 24-10-2016 13:00:32Build: 5203
LABSEN1 - 03_21 Beta NoForce 20161024130032 5203.firm
Supporting BaseSensor for BaseSpion
BaseSensor and LabSensor - version 3.18
Date: 08-02-2016 11:35:40Build: 5162
LABSEN1 - 03_18 Beta NoForce 20160208113540 5162.firm
Spectrometer can now be reset from the Light Inspector software.
BaseSensor and LabSensor - version 3.17
Date: 29-07-2015 21:40:43Build: 5152
LABSEN1 - 03_17 Beta NoForce 20150729214043 5152.firm
Laser distance can now be measured by only pushing measure button. Fixes: More stable laser measurement, Power push and Meas push delay implemented
BaseSensor and LabSensor - version 3.16
Date: 10-02-2015 16:47:11Build: 5132
LABSEN1 - 03_16 Beta NoForce 20150210164711 5132.firm
Long RJ45 cable connection problem fixed. Write to EEprom fixed, Laser board power and remote control. Spectrometer bad offset power reset fixed
BaseSensor and LabSensor - version 3.14
Date: 15-01-2015 17:03:12Build: 5116
LABSEN1 - 03_14 Beta NoForce 20150115170312 5116.firm
Laser board power and remote control. Spectrometer bad offset power reset fixed
BaseSensor and LabSensor - version 3.13
Date: 16-11-2014 16:55:52Build: 5113
LABSEN1 - 03_13 Beta NoForce 20141116165552 5113.firm
Laser remote control. Spectrometer bad offset power reset fixed, First release of LabSensor firmware
BaseSensor and LabSensor - version 3.12
Date: 26-08-2014 19:12:33Build: 5101
LABSEN1 - 03_12 Beta NoForce 20140826191233 5101.firm
Spectrometer bad offset power reset fixed, First release of LabSensor firmware
_________________________________________________________________________________________________________________
Date: 26-09-2018 16:58:15Build: 0
FLICK01 - 01_25 Beta NoForce 20180926165815 0.firm
Supporting dynamic sample rate enabling PstLM measurements. Oversampling with filtering giving higher dynamic range and less noise.
LabFlicker - version 1.19
Date: 26-04-2018 13:44:16Build: 0
FLICK01 - 01_19 Beta NoForce 20180426134416 0.firm
Changed sample rate to 50000Hz and the sample size has been change to fit with 1 second of measurement. Requires Light Inspector 5.37.
LabFlicker - version 1.18
Date: 06-12-2017 13:36:22Build: 0
FLICK01 - 01_18 Beta NoForce 20171206133622 0.firm
Increase scan size to get 0.1 second total sample time.
LabFlicker - version 1.16
Date: 20-11-2017 16:25:44Build: 0
FLICK01 - 01_16 Beta NoForce 20171120162544 0.firm
Flicker measurement second version. Including serial number readout function.
LabFlicker - version 1.15
Date: 03-10-2017 11:25:31Build: 0
FLICK01 - 01_15 Beta NoForce 20171003112531 0.firm
Flicker measurement first version
_________________________________________________________________________________________________________________
Date: 11-03-2013 15:28:54Build: 4407
VX01 - 01_88 Beta NoForce 20130311152854 4407.firm
Now smoother 44Hz DMX from USB when using vdesigner 3.31 or never. Trackwheel sensitivity increased. First 4PP version. DMX 44hz. Previous dmx frames in this current frame, bug fix beta1.
VX01 Controller - version 1.87
Date: 03-09-2012 16:47:48Build: 4379
VX01 - 01_87 Beta NoForce 20120903164748 4379.firm
Trackwheel sensitivity increased. First 4PP version. DMX 44hz. Previous dmx frames in this current frame, bug fix beta1.
VX01 Controller - version 1.86
Date: 27-04-2012 11:59:46Build: 4376
VX01 - 01_86 Beta NoForce 20120427115946 4376.firm
First 4PP version. DMX 44hz. Previous dmx frames in this current frame, bug fix beta1.